Skip to content
120 FPS Test

Frame rate · refresh rate

120 FPS Test

Check whether your screen really runs at 60, 120, 144 or 240 Hz. The test starts on its own and shows your live frame rate, frame times and dropped frames. Nothing to install.

Current frame rate

–FPS

Detected refresh rate

–Hz

Measuring… keep this tab in front and the window on the screen you want to test.

Frame time. Average time between frames over the last second.
–
Average. Frames per second across the whole session.
–
1% low. Frame rate of the slowest 1% of recent frames.
–
Min / Max. Lowest and highest one-second frame rate this session.
–
Dropped. Refreshes that passed without a new frame.
–
Jitter. Standard deviation of frame times. Lower is smoother.
–
Screen. Screen resolution in CSS pixels and the device pixel ratio.
–
Running. Measured time, excluding pauses and background time.
–

Motion comparison

The same saucer at 120 fps, at your full frame rate, and at half and a quarter of it. Follow each one with your eyes: higher rates look smoother and sharper.

Motion speed

How to test your FPS and refresh rate

  1. 1Put the browser on the screen you want to test. With several monitors, the browser matches the one its window sits on.
  2. 2Wait a few seconds. The refresh rate appears after about 60 frames and settles within a couple of seconds.
  3. 3Leave the tab in front. Browsers pause or slow down pages in background tabs and minimised windows.
  4. 4Watch the motion comparison. At 120 Hz and above, the 120 fps lane should look clearly smoother than the slower lanes below it.

Why is my FPS capped at 60?

If a 120 Hz or 144 Hz screen shows 60 FPS here, one of these is almost always the cause.

The display is set to 60 Hz

Windows: Settings > System > Display > Advanced display > Choose a refresh rate. macOS: System Settings > Displays > Refresh rate. Android: Settings > Display > Smooth motion or Refresh rate.

The cable or port cannot carry it

Older HDMI ports and cheap cables top out at 60 Hz at high resolutions. Use DisplayPort or HDMI 2.1 and plug into the graphics card, not the motherboard.

Battery or energy saving is on

Low Power Mode on iPhone, Battery Saver on Windows and Android, and Chrome’s Energy Saver all cap the frame rate, sometimes to 30 FPS. Plug in or turn them off and test again.

The window is on another monitor

The browser syncs to the screen the window sits on. With a 60 Hz and a 144 Hz monitor side by side, drag the window fully onto the fast one and reload.

Safari limits pages to 60 FPS

Safari on iPhone and iPad has long limited web pages to 60 FPS even on ProMotion screens. On some iOS versions you can lift it under Settings > Apps > Safari > Advanced > Feature Flags by turning off “Prefer Page Rendering Updates near 60fps”.

Hardware acceleration is off

Without GPU acceleration browsers can struggle to keep up. In Chrome and Edge check Settings > System > Use graphics acceleration when available.

Refresh rates and frame times

Frame time is how long each frame stays on screen: 1000 ms divided by the refresh rate. A frame that takes longer than that misses a refresh and shows up as a stutter.

Refresh rateFrame timeTypical devices
30 Hz33.33 msBattery saver modes, some TVs and remote desktop sessions
60 Hz16.67 msMost laptops, office monitors, TVs and older phones
75 Hz13.33 msBudget and office monitors
90 Hz11.11 msMid-range phones and VR headsets
120 Hz8.33 msiPhone Pro, iPad Pro, flagship Android phones, gaming laptops and newer TVs
144 Hz6.94 msEntry-level gaming monitors and laptops
165 Hz6.06 msMid-range gaming monitors and laptops
240 Hz4.17 msCompetitive gaming monitors, including many OLEDs
360 Hz2.78 msEsports monitors
480 Hz2.08 msThe fastest esports monitors, OLED and TN

Overclocked your monitor? Check for frame skipping

A monitor pushed past its rated refresh rate can report the new rate but quietly drop frames. The FPS counter cannot see that, because the browser still delivers every frame. A camera can. The frame skipping test lights one square per frame so a long-exposure photo shows any gaps.

FPS test FAQ

How does this FPS test work?

Browsers draw a new frame each time the screen refreshes and tell the page when it happens. The test times every one of those frames, counts how many arrive each second and takes the typical interval between them to work out the refresh rate. Everything runs in your browser and nothing is uploaded.

Why does my 120 Hz or 144 Hz screen only show 60 FPS?

The most common causes are a display still set to 60 Hz in the system settings, a cable or port that cannot carry the higher rate, battery saver or Low Power Mode, the browser window sitting on a second 60 Hz monitor, and Safari on iPhone and iPad, which limits web pages to 60 FPS by default.

What is the difference between FPS and refresh rate?

Refresh rate, in hertz (Hz), is how many times per second the screen can show a new image. Frames per second (FPS) is how many new images the computer actually produces. You only see the benefit of a 144 Hz monitor when something delivers 144 FPS to it, and FPS above the refresh rate is never shown.

How accurate is an online FPS test?

On a steady system the detected refresh rate is exact to within a hertz, because it is taken from the typical frame interval over several hundred frames. The live FPS figure can move by a frame or two as the browser does other work. It measures what the browser delivers, which is also what you see.

Does this test my game FPS or graphics card?

No. It shows how smoothly your browser renders on this screen, which confirms the refresh rate is working. Game frame rates depend on the game and its settings, so use an in-game counter, the Steam overlay or your GPU software for those.

What are 1% lows and dropped frames?

1% low is the frame rate of the slowest one percent of recent frames. It shows stutter that an average hides. A dropped frame is a screen refresh that passed without a new frame, for example a 25 ms gap on a 120 Hz screen counts as two dropped frames.

Can it measure 240 Hz, 360 Hz or 480 Hz monitors?

Yes. There is no upper limit in the test itself. Chrome, Edge and Firefox on desktop follow the monitor’s refresh rate, so a 240 Hz or 480 Hz monitor shows 240 or 480 FPS when the system keeps up.

Why does the FPS number jump around?

Background tabs, extensions, video playback and other apps compete for the same processor and graphics card. Close them for a cleaner reading. If the number keeps dipping, check the frame time graph: amber bars are frames that took more than one and a half times as long as they should, red bars more than two and a half times.

What is the motion comparison for?

It moves the same object at 120 fps, at your full frame rate, and at half and a quarter of it. Following each with your eyes shows what a higher refresh rate buys: smoother motion and a sharper moving image. On a screen below 120 Hz, the 120 fps lane is capped at the refresh rate and looks the same as the full-rate lane. On a 120 Hz screen, if the 120 fps lane looks no smoother than the 60 fps one, the screen is probably not running at 120 Hz.

Does the FPS test work on phones and tablets?

Yes. It works in any modern mobile browser with nothing to install. Android phones with 90 Hz or 120 Hz screens show their full rate in Chrome. On iPhone and iPad, Safari usually shows 60 FPS even on ProMotion screens because of a browser limit, not the display.